Honda Spree and Elite 50 Forums

So far...

I also considered a piece of brake line in between the throttle slide and the top that screws on top the carb to limit the slide pull.

Here is my near death experience with a spree today:
I re-wired the machine for kick-start only, and just the basics. No lights, blinkers etc. Got rid of the entire ...

Amen on the throttle stop, I would like the machine to go thru some dirt without bogging out. The spree wont hack in it in any type of sand or dirt without a geardown. I have an extra block so I am thinking about cutting it to fit a gy6 clutch sheve which will hopefully help.

Here is her on the electric, the battery runs out in 40 mins and takes 8hrs to charge

For Christmas last year the girlfriend and I got her 8yr old daughter a electric dirt bike. She is ready for the next thing, i will be getting her a xr100 next year but need something to get her by until then.
I spot a busted down spree in corner of my garage and go to work. Motor is froze up ...

Tore the motor apart yesterday to swap cases and found drive side crank bearing has slop and all three bearings/seals the in the final drive also need to be replaced. Looking at a total cost of $250+ to fix so I am buying another 2001 sa50p with 450 original miles on it :smile: for $500, no title ...

Will my intake, cylinder and pipe fit this block?

http://appleton.craigslist.org/mcy/3212947239.html

Did not support the block correctly and broke the engine bushing tab off

Need a right side engine block http://www.hondaspree.net/phpBB3/viewto ... =2&t=24811

Could have someone tig it back on but would I trust it at 60mph...

Has just started doing this vibration within the last 50 miles, I used to top out at 60mph, smooth as butter and feel safe doing it, not so much now :confused:

The only thing I could find was slop in the motor bushings, they are really bad...

I pushed them out by hand with a socket extension and ...

So I got a wom wom woom woom wooom wooom woooom woooom vibration going on anywhere above 40mph. Replaced belt and rollers as advised, no change. I have noticed that if I am crusin at 40 and roll into the gas it goes away untill my speed catches up to the throttle then it comes back. Regardless of ...

Thanks I will replace them

Zx50 seems to be the most common and easy to get but I doubt it matches honda in quality of parts. How long would stock zx50 crank bearings hold up to a bbk.....
Or would a af16 bolt into a zx50 without major mods? I think that would be the way to go

Those first gen zumas are cheap around here (for ...

Was it the worn var causing the problem? I recently started noticing a vibration at 50mph and above. Now it is worse and starts at 40mph and above
Its a woooooooom-wooooooooom-woooooom-wooooooom-woooom-woooom-wooom-wooom-woom-woom-woom-wom-wom-wom

If i accelerate to 40 and hold it there the ...

So what would be the second choice to an elite? I refuse to work on anything made in china, Taiwan I can deal with...
One of my buds built a eton beamer last year with a 70cc kit and pipe, got me excited and actually a little worried.
But what a dog it was, went 52mph but took forever to get there ...

I currently have 01 SA50 72cc Malossi/Ct Intake/28mm OKO Carb #130 main
PG Long/9:1gears/RuimaVar6/7G/1.5K springs Chinese moped Spedo
60mph top speed, 50mph crusin speed, Daily Driver ~6k miles

I love the elite and its plenty fast, but I am curious about the zumas.

Looked over at zumaforums.net ...