Honda Spree and Elite 50 Forums

Look at eBay.it that’s ebay Italy and type pgo star cilindro. I guess that’s cylinder in Italian?

Happy birthday to me.
Pic from High Valley camp and airfield, Suches, GA.
Taken by vintagegarage a few years ago.


Happy belated bday Mike. Hope you had a good one!!!

As to your carb tuning. Remember. You can remove the slide pull the spring. Pull the needle and there’s a clip for fine ...

You could always buy some Japan alloy wheels. They’re 4x110? Bolt pattern and a ruckus/zoomer rear hub bolts to them and for front i use the elite 150 front hub. Same bolt pattern. But it has 105mm diameter drum brake. For upgraded stopping power.

If I remember correctly. The axle just bolts into a bearing that’s pressed into case. Here’s am 85 piece and it’s cheaper. I’ve had a few gyros down to bare cases. That side cover just bolts onto the engine cases. You have to remove that cover to get the cooling fan off. And remove the flywheel and ...

Left rear wheel is the coaster side. What was your issue? I have some spare parts and will help you any way I can. I owe you for those parts that helped me out a couple years ago. 😉

Exact problem not yet diagnosed. Noticed the wheel showing some wobble.
Wheel is bolted securely to the brake ...

hey mike. check your float level... too high will caue your exact issue.. lower it a 1/2 a mmm and see if it fixes your problem i dont think you have a jetting issue
Okay...good stuff HR59...and seems to make sense.
Will keep this in mind next March when I pull the Gyro out of storage.
Had a ...

I would get a complete gy6 racing pulley with vented clutch bell off fleabay. It’s the zx diameter pulley with different groove choices a red contra spring new clutch with red clutch springs and a vented clutch bell. Easiest and best and cheapest option in my opinion. When you get it. Take it apart ...

It was 38mm lenght and there was a hole 12mm. I had to drill to 14mm to fit it to af18e.

And with lenght Im still waiting for malossi belt and zx pulley.

its this vari: https://www.2hmoto.cz/variator-ip000337



if i remember correctly, a racing gy6 rear pulley is the same diameter as the zx ...

stock cvt vs in-part ( i had to drill boss)... and do you think that i should grind case more in that spot?
thank you

what are the measurements on the variator boss? i had to drill out the dio variator boss to fit on my ab07. with my newly found info on the pgo star1. malossi and polini both ...

hey mike. check your float level... too high will caue your exact issue.. lower it a 1/2 a mmm and see if it fixes your problem i dont think you have a jetting issue

harleyracer59: i was talking about between flywheel and pickup coil (from the outside). Some bikes have in service manual gap between these two parts... usuallly 0,45mm

https://i.ibb.co/BZT3HT1/s-l1200.jpg



its been a while since ive had a flywheel off one of my hondas... lol for some ...

Parts list
I used a Malossi Gyro cylinder for the Japanese TG50 spec engine. Based on this Treatland review, it is the same stroke as the Gen 1 Aero:
https://www.treatland.tv/malossi-70cc-47mm-cylinder-for-honda-GYRO-TG50-and-p/malossi-gyro-kit-31-6170.htm

"ports look like af01 ports. which is ...

Its probably an af16e or af18e with an af05e rear trans cover...



i think this is the correct answer to what engine is in this guys scooter. looking at that last pic he poste, 2 thingsverified that its for sure not a spree af05. 1, it has a 4 bolt reed block intake, spree engine only has a 2 ...

I’m sure there Is it but I think it’s kinda fixed. I don’t know how you would adjust? Your stator is bolted down centered around the flywheel shaft. I’ve used an offset woodruff key to adjust base timing. But the crankshaft flywheel and stator are all self centered by bearings and cases.

Modified ab07 cases to fit af01 lead bbk