This is how it's done my children.

benjammer112 · Post by **benjammer112** » Wed Jul 20, 2011 12:09 am

this is how it's done, 6.5 hp motor bolted to the floor board with some welded on pulleys, the coolest/lamest deathtrap ever.

wood10214 · Post by **wood10214** » Wed Jul 20, 2011 12:14 am

Look scary to me

fastplastic · Post by **fastplastic** » Wed Jul 20, 2011 8:24 am

wow epic fail good luck

Wheelman-111 · Post by **Wheelman-111** » Wed Jul 20, 2011 8:44 am

Greetings:

Dude! Swap in a Briggs and Stratton!!

Does it function? If so it is the coolest resurrection ever! Maybe install some footpegs somewhere...

dun rite · Post by **dun rite** » Wed Jul 20, 2011 11:00 am

Inventive. i'd suggest a belt guard though

motormike · Post by **motormike** » Wed Jul 20, 2011 12:42 pm

Footpegs??..........belt guard??..........Naw, man.....what it needs is a bottle..........

Palero2003 · Post by **Palero2003** » Wed Jul 20, 2011 1:54 pm

Thinking outside of the box I guess lol. But if works right on!

mousewheels · Post by **mousewheels** » Wed Jul 20, 2011 3:04 pm

Belt guard+++
Looks like the OEM engine still has it's intake and carb. Are you running the injection pump to oil the case bearings?

If the piston/cyl is intact, a check valve in place of the spark plug and plumbing would make a low output/low pressure compressor. Maybe enough to drive an air brush and paint itself - or run a set of air horns.

Wheelman-111 · Post by **Wheelman-111** » Wed Jul 20, 2011 7:19 pm

Greetings:

Quoth The Mouse:

If the piston/cyl is intact, a check valve in place of the spark plug and plumbing would make a low output/low pressure compressor. Maybe enough to drive an air brush and paint itself - or run a set of air horns.

Now ah don' care who y'are or how much money ya got, tha's some funny stuff rat thar!

At 9:1 compression ratio, you'd have something like 135PSI. It could keep its own tires inflated too!

You do make a good point about keeping the bearings lubed, but I guess one could lose the connecting rod and piston altogether and just squirt some oil down the plug hole once in a while.

motormike · Post by **motormike** » Wed Jul 20, 2011 9:29 pm

I nominate this for an award....."Best Innovative Thought".......makes me sit back wonder what kind of mind was at work to think this one up......Rah!.....Rah!.....Rah!..

maddog · Post by **maddog** » Thu Jul 21, 2011 12:51 am

you are now qualified to work at a John Deere plant

fastplastic · Post by **fastplastic** » Thu Jul 21, 2011 7:38 pm

maddog wrote:you are now qualified to work at a John Deere plant

Bear45-70 · Post by **Bear45-70** » Thu Jul 21, 2011 9:02 pm

fastplastic wrote:
maddog wrote:you are now qualified to work at a John Deere plant

First time I have ever seen Maddog say anything I could agree with.

Trafficjamz · Post by **Trafficjamz** » Thu Jul 21, 2011 9:48 pm

I hope this was meant to be a joke.

There is no way this piece of $hit runs or moves.

The front pulley is a clutch mounted backwards

with no nut to hold it in place.

The clutch pucks are just flinging around all over the place, with no bell to keep them from flying off.

Wheelman-111 · Post by **Wheelman-111** » Thu Jul 21, 2011 10:04 pm

Greetings:

Suddenly TrafficJamz = Buzzkill!

The front engine would make a hellova Dio starter.

Honda Spree and Elite 50 Forums

This is how it's done my children.

This is how it's done my children.

Re: This is how it's done my children.

Re: This is how it's done my children.

Re: This is how it's done my children.

Re: This is how it's done my children.

Re: This is how it's done my children.

Re: This is how it's done my children.

Re: This is how it's done my children.

Re: This is how it's done my children.

Re: This is how it's done my children.

Re: This is how it's done my children.

Re: This is how it's done my children.

Re: This is how it's done my children.

Re: This is how it's done my children.

Re: This is how it's done my children.