Elite [SB50] 50
Moderator: Moderator
-
- Goped
- Posts: 68
- Joined: Sat Dec 24, 2011 9:34 pm
- Location: Sacramento CA
Re: Elite 50
Did a compression check and it has about 89 pounds
-
- CBR1000RR
- Posts: 3675
- Joined: Thu Mar 05, 2009 9:02 pm
- Location: Iowa, USA
Re: Elite 50
Time to rebuild.lovemyelite50 wrote:Did a compression check and it has about 89 pounds
motormike wrote:Errands become adventures.
-
- Goped
- Posts: 68
- Joined: Sat Dec 24, 2011 9:34 pm
- Location: Sacramento CA
Re: Elite 50
Oh. How many pounds should it have?
-
- Goped
- Posts: 68
- Joined: Sat Dec 24, 2011 9:34 pm
- Location: Sacramento CA
Re: Elite 50
And also the clutch is engaging at an idol of like 500 Rmps how could I make it so the engine would half to rev and then make the clutch pads grab
Re: Elite 50
with that low compression you may want to take the head and cylinder off and inspect the piston, rings, and cylinder walls. low compression is the likely culptrit of your loss of power. it should be more like 110 also the crankcase oil sleas tend to wear out over 20 years
1986 Spree/ Eve af16 swapped 65cc Prodigy vari 8g 9:1 Ruima gears
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged
1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
21mm OKO 42/100 32:1 45mph kymco zx exhaust
1994 Elite S 17.5mm Arreche, Daytona reeds, SEF ramp, pump plugged

1987 Elite SE50 af16 swapped
1989 Elite E SB50p
2003 Yamaha Zuma
-
- CBR1000RR
- Posts: 3675
- Joined: Thu Mar 05, 2009 9:02 pm
- Location: Iowa, USA
Re: Elite 50
You need stiffer graber springs in the clutch. They go soft over time.
motormike wrote:Errands become adventures.
-
- Goped
- Posts: 68
- Joined: Sat Dec 24, 2011 9:34 pm
- Location: Sacramento CA
Re: Elite 50
Do you think something could be clogged in the carb? Because I am able to turn the air fuel mixture screw in all the way and it still runs great, all the way in? Or possibly a vaccine leak.
Re: Elite 50
Not sure on the a/f screw, but the compression would not be affected much by the carb being clogged. When you did the compression test did you do it at WOT?lovemyelite50 wrote:Do you think something could be clogged in the carb? Because I am able to turn the air fuel mixture screw in all the way and it still runs great, all the way in? Or possibly a vaccine leak.
2000 Elite SR50 -THE PURPLE NURPLE
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
50mm BBK (tai)
26mm OKO (round slide) 135 Main Jet
V-8 pipe
39/18 secondary gears (7.583:1 ratio)
36 grams in Prodigy variator
Malossi Delta Clutch & WIng Bell- Thanks RED EFT
65mph GPS (on the freeway)
Re: Elite 50
a/f screw all the way in and it still runs generally means its time to rebuild the carb or replace it does it make a difference if you turn it out all the way also check the intake mani for leaks some times that can give abnormal carb tuning symptoms
Re: Elite 50
Whether it does this or not has NOTHING to do with how it will run with the tires on the road.deuce217 wrote:................................ Will it rev well on the kickstand with no load?
Bear 45/70

'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree

'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
Re: Elite 50
Maybe but I would suspect a leaking petcock with fuel coming into the system thru the vacuum line before tearing the carb apart. Clear fuel and vacuum lines would let you see if this was happening.b.ludwig wrote:a/f screw all the way in and it still runs generally means its time to rebuild the carb or replace it does it make a difference if you turn it out all the way also check the intake mani for leaks some times that can give abnormal carb tuning symptoms
Bear 45/70

'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree

'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
Re: Elite 50
Maybe but I would suspect a leaking petcock with fuel coming into the system thru the vacuum line before tearing the carb apart. Clear fuel and vacuum lines would let you see if this was happening.
_________________
very true forgot about that part
_________________
very true forgot about that part
-
- CBR1000RR
- Posts: 3675
- Joined: Thu Mar 05, 2009 9:02 pm
- Location: Iowa, USA
Re: Elite 50
If the engine won't wind out on the stand, it won't wind out on the road. I sometimes use this to test pipe symptoms before pulling the pipe.Bear45-70 wrote:Whether it does this or not has NOTHING to do with how it will run with the tires on the road.deuce217 wrote:................................ Will it rev well on the kickstand with no load?
motormike wrote:Errands become adventures.
-
- CBR1000RR
- Posts: 3675
- Joined: Thu Mar 05, 2009 9:02 pm
- Location: Iowa, USA
Re: Elite 50
Amateurs all. Not necessarily true, I've had engines that ran for crap in neutral but in gear worked just fine. *, if the exhaust is plugged so bad that it won't rev with no load, it is not gonna even move the scooter with the tire on the ground. An engine requires so little air to rev unloaded that you never ever get the throttle above 1/4 and more likely an 1/8th. Which means you have proven NOTHING.eliteguy50 wrote:If the engine won't wind out on the stand, it won't wind out on the road. I sometimes use this to test pipe symptoms before pulling the pipe.Bear45-70 wrote:Whether it does this or not has NOTHING to do with how it will run with the tires on the road.deuce217 wrote:................................ Will it rev well on the kickstand with no load?
Bear 45/70

'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree

'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree