stock exhaust?

[eliteguy50]

so $500 is a garuntee to get the wheel up then i wanna do it all motor and gears kevlar belt aftermarket cdi coil all tha good s***

Being able to wheelie pretty much guarantees * poor top speed. You can not have everything.

FYI the stock CDI is not REV limited and just move your pulse generator to get the 4┬░ for free. OH and the aftermarket box is gonna leave you stranded somewhere. They die a lot.

Don't forget to account for the short wheelbase of the spree and how far back the rider weight is. A frame designed for 1.5 or 2 claimed hp and then you swap in a 9hp engine. Top speed of 55 and still pulls wheelies. The short base just makes it more sketchy. Also, remember to check your rake when relocating your shock mount.

[eliteguy50]

I like my 2.75*10 bridgestone hoops. They are sticky enough for the spree and they don't break the bank.

[b.ludwig]

yea 4 degress is the number i mentioned but that was the setting the box set which you recommended to not use so i was askin wat would you do

[Bear45-70]

yea 4 degress is the number i mentioned but that was the setting the box set which you recommended to not use so i was askin wat would you do

You will have to figure that out. Try degreeing the flywheel and then you will have a reference, but 4┬░ isn't much. I have found that screwing with the timing on 2 strokes will result in a burnt up engine with little if any difference in performance on a street machine. On the race track, yes I played with timing allot, on the street, no.

[swimmingfree]

timing is some thing you shod not change on the bottom of the timing crive its the top end you need to change it..
4 degrees is a huge change 1 maybe 2 may help but your motor will run hotter ( i think ) and it will melt down as your driving it but if you only doing a 1/4 at a time shood be fine..
by the way have you put a timing lite on the motor yet ???
there is marks on the fly wheel and the holes on the pick up so it can be mover a small amount ..
swimmingfree

[b.ludwig]

ok so i found a 48mm bbk with a 21mm carb intake mani adapter new throttle cable 16*82 secondary and its 335 bucks yay nay your thoughts

[Bear45-70]

Tazland001 here on the forum (chop*chop123 on flea-bay) is the only one with a BBK, a 21 OKO, manifold with adapter and gears for the Spree. So of course we like his stuff.

[Mystic]

do the thang, thats the best you are going to get for the spree i think it does 40mph maybe more if you build your own muffler

[eliteguy50]

do the thang, thats the best you are going to get for the spree i think it does 40mph maybe more if you build your own muffler

If you can find the rare es pipe. That is the best flow from a bolt on manufactured pipe.

[b.ludwig]

yup thats the guy i like the kit specially for the gears and the liitle stuff it has with it least now i know i can get it here to bout two weeks ill be ready to get one fyi taz

[b.ludwig]

ok so off topic but i wanna do some cool cosmetic stuff like pointless guages and such i have a vacuum gauge and a volts gauge i wanna add a tach tho anyone know where i can find a tach for a one cylinder

[Carnie]

Try vapor trail tech computers. Has all the gauges in one.

[Bear45-70]

http://www.ebay.com/itm/200694081626?ss ... 213wt_1185

and

http://www.ebay.com/itm/380400018746?ss ... _500wt_969

[b.ludwig]

i like and i want i think i will buy ne this pay check

[b.ludwig]

Honda - WEIGHT SET, CLUTCH
Item: 22535-GK8-325
$39.73 $39.73


as seen on hondapartshouse.com 86 spree weightset still available brand new $46 shipped