My 85' spree does run.. but needs some work...

abreen89 · Post by **abreen89** » Sat Mar 17, 2012 9:51 pm

7 spark plug plate has some metal burrs on it...

abreen89 · Post by **abreen89** » Sat Mar 17, 2012 9:51 pm

abreen89 · Post by **abreen89** » Sat Mar 17, 2012 9:52 pm

Let me know what u guys think I should do the cylinder looks good I don't see any major ware marks or scratches at all thanks guys!

abreen89 · Post by **abreen89** » Sat Mar 17, 2012 10:42 pm

i did just noticed this on the cylinder i dont know if its how its suppose to be but i think its worth metioning.

abreen89 · Post by **abreen89** » Sun Mar 18, 2012 1:35 am

will the top end in this ad fit my '85 spree?
http://www.ebay.com/itm/Honda-Spree-Sco ... 3a716dbf9a

Mystic · Post by **Mystic** » Sun Mar 18, 2012 9:52 am

no it wont I dont even know why they have that labeled for a Spree, it looks like a bore for a horizontal minarelli or a china cloned gy6

abreen89 · Post by **abreen89** » Sun Mar 18, 2012 12:11 pm

Alright thanks mystic

abreen89 · Post by **abreen89** » Sun Mar 18, 2012 11:29 pm

alright guys after talking to taz and looking at my options i decided to get a new 41mm kit so when i get it ill put it all back together and see what happens. Thanks!

abreen89 · Post by **abreen89** » Sun Mar 25, 2012 9:44 pm

Alright guys i got taz's new top end in the mail. i spent today getting everything cleaned up and tommorow going to borrow my buddies torque wrench. Question though..... is there an easy way to get piston clips in? (the clips that holds in the pin) i tried and tried i didnt want to bend the clip out of wack but i can not get them in!!! right now they are shaped lie circles and at then end is bent inward almost look like a letter e but not connected obviously. Any tips will be greatly appreciated!

Mystic · Post by **Mystic** » Mon Mar 26, 2012 9:35 am

use a pair of needle nose pliers. You can put the carb side clip in the piston with it off the conrod. hold the end that is bent in toward the center, place the other end into the clip groove on the piston then twist with the needle nose toward the end that is already in the groove to make the clip slightly smaller and it should slip into the groove

abreen89 · Post by **abreen89** » Mon Mar 26, 2012 11:15 am

Thanks mystic the piston brings tax sent me look identicle are they suppose to unthought one was suppose to be a little different then the other

abreen89 · Post by **abreen89** » Mon Mar 26, 2012 3:33 pm

I GOT IT RUNNING!!!! With help from you guys of course! I torqued down the head and she started right up! Now the fun begins... Tuning! Everything seems to work except for the blinkers.... Any ideas?

ragtop89 · Post by **ragtop89** » Mon Mar 26, 2012 3:36 pm

Make sure you baby it, I think you have to heat cycle that?

Honda Spree and Elite 50 Forums

My 85' spree does run.. but needs some work...

My 85' spree wont run????

My 85' spree wont run????

My 85' spree wont run????

My 85' spree wont run????

My 85' spree wont run????

Re: My 85' spree wont run????

Re: My 85' spree wont run????

Re: My 85' spree wont run????

My 85' spree wont run????

Re: My 85' spree wont run????

Re: My 85' spree wont run????

Re: My 85' spree wont run????

My 85' spree wont run????

Re: My 85' spree wont run????

Re: My 85' spree wont run????