how much is too much? modding the jug

Trafficjamz · Post by **Trafficjamz** » Wed Mar 21, 2012 3:44 pm

Is it ok to cut the section at the bottom of the jug that can be seen through the intake widows in the block ?

I will try to take a picture of what I am talking about.

bakaracer · Post by **bakaracer** » Wed Mar 21, 2012 4:11 pm

yeah you can. look at your stroker bore as an example.

Trafficjamz · Post by **Trafficjamz** » Wed Mar 21, 2012 5:36 pm

bakaracer wrote:yeah you can. look at your stroker bore as an example.

Yeah the 125 jug has no side skirts at all.

the polini jug has very high skirts.

iceman77 · Post by **iceman77** » Wed Mar 21, 2012 10:51 pm

is that my bore? if so i like the way it's looking.

TJ

Trafficjamz · Post by **Trafficjamz** » Wed Mar 21, 2012 11:00 pm

iceman77 wrote:is that my bore? if so i like the way it's looking.

TJ

Yes sir. Now I am just waiting for autotech355 to send gears. tiawan is far away

some port work by jamz

side skirts compared to polini bore

bakaracer · Post by **bakaracer** » Wed Mar 21, 2012 11:18 pm

if your going to leave the intake port on the block that size, at least round the top and smooth out the side more so it doesnt cause to much turbulance.

Trafficjamz · Post by **Trafficjamz** » Wed Mar 21, 2012 11:21 pm

bakaracer wrote:if your going to leave the intake port on the block that size, at least round the top and smooth out the side more so it doesnt cause to much turbulance.

I will do that

kingkamehameha · Post by **kingkamehameha** » Thu Mar 22, 2012 12:32 am

Looks good traffic. What size carb and jets you planning on running? Does a block with a matched boost and ported intake port require bigger jets because there is more flow or smaller jets because it runs more efficient????!!

Trafficjamz · Post by **Trafficjamz** » Thu Mar 22, 2012 12:37 am

ported = smaller jets

Trafficjamz · Post by **Trafficjamz** » Thu Mar 22, 2012 1:30 am

Trafficjamz wrote:
bakaracer wrote:if your going to leave the intake port on the block that size, at least round the top and smooth out the side more so it doesnt cause to much turbulance.
I will do that

I got it opened up a little more.

I will go back over it tomorrow with some cartridge rolls.

damnSA50 · Post by **damnSA50** » Tue Mar 27, 2012 3:03 am

On my Malossi bbk for the af05 the exhaust port isnt quite circular, think I should bore it out? Im thinking I should wait till I get a bigger carb first, this stock one might be the pin in my grenade.

damnSA50 · Post by **damnSA50** » Tue Mar 27, 2012 3:04 am

Oh ya traffic, I show everyone I know your photobucket race vs the honda civic or whatever that thing was. Thats a bad * scooter.

swimmingfree · Post by **swimmingfree** » Tue Mar 27, 2012 8:24 am

hopping to see what kind of rpm and what other info you get from this motor...good read so far ... what is the gool of this motor racing ???
swimmingfreee

iceman77 · Post by **iceman77** » Wed Mar 28, 2012 8:21 am

swimmingfree wrote:hopping to see what kind of rpm and what other info you get from this motor...good read so far ... what is the gool of this motor racing ???
swimmingfreee

nope not racing but a daily driver

TJ

Honda Spree and Elite 50 Forums

how much is too much? modding the jug

how much is too much? modding the jug

Re: how much is too much? modding the jug

Re: how much is too much? modding the jug

Re: how much is too much? modding the jug

Re: how much is too much? modding the jug

Re: how much is too much? modding the jug

Re: how much is too much? modding the jug

Re: how much is too much? modding the jug

Re: how much is too much? modding the jug

Re: how much is too much? modding the jug

Re: how much is too much? modding the jug

Re: how much is too much? modding the jug

Re: how much is too much? modding the jug

Re: how much is too much? modding the jug