i just assebmled the Taz "stage 3" kit on my spree, and am very near the point where it's time to fire it up. all i need to do is sort out my oiling system.
so i searched and found that a lot of people say to disable the factory pump, and just run straight up premix. i've somehow got myself convinced that i should just screw another barb in the CT manifold, run the stock oiler, AND a little pre-mix on top of it. seems a little more logical than destroying a perfectly good oil pump.
thanks in advance
oil pump/BBK question
Moderator: Moderator
-
SuprasNsprees
- Elite
- Posts: 475
- Joined: Mon Jun 20, 2011 2:05 pm
- Location: saint louis
- Contact:
oil pump/BBK question
'86 Honda Spree : taz stage3 w/ mild porting, head milled 0.015", and pulley mod. 2k+ mies on kit
'80 Puch Magnum MKII
'78 Maxi Newport. Polini 64cc case matched, hi comp head, Rito alum crank, delorto 21mm race, etc.
'78 PA50 Hobbit
'80 Puch Magnum MKII
'78 Maxi Newport. Polini 64cc case matched, hi comp head, Rito alum crank, delorto 21mm race, etc.
'78 PA50 Hobbit
Re: oil pump/BBK question
Some have mentioned tying the pump open as well.
Re: oil pump/BBK question
All that tying the pump wide open is oils the * out of it at lower RPM.ragtop89 wrote:Some have mentioned tying the pump open as well.
SuprasNsprees, The pump/partial; pre-mix thing will work.
Bear 45/70
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
-
SuprasNsprees
- Elite
- Posts: 475
- Joined: Mon Jun 20, 2011 2:05 pm
- Location: saint louis
- Contact:
Re: oil pump/BBK question
great! thanks, bear
'86 Honda Spree : taz stage3 w/ mild porting, head milled 0.015", and pulley mod. 2k+ mies on kit
'80 Puch Magnum MKII
'78 Maxi Newport. Polini 64cc case matched, hi comp head, Rito alum crank, delorto 21mm race, etc.
'78 PA50 Hobbit
'80 Puch Magnum MKII
'78 Maxi Newport. Polini 64cc case matched, hi comp head, Rito alum crank, delorto 21mm race, etc.
'78 PA50 Hobbit
Re: oil pump/BBK question
Speaking of pre-mix, did you get your 24mm carb on your NH80 yet bear? Wondering what mix you had to run.
Re: oil pump/BBK question
No, the scooter is in my shop and the parts are there but I got kicked back onto restricted duty. I see the doc tomorrow and hope to be released again.
Bear 45/70
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
'83 Aero 80 X 3
'84 Aero 80 X 3
'85 Aero 80
'84 Aero 125 X 2
'84 Aero 125
'84 Aero 125 X 2
'85 Aero 50
'85 Spree
Re: oil pump/BBK question
Ah, sorry to hear that. Hope you get the ok from the doc!
-
SuprasNsprees
- Elite
- Posts: 475
- Joined: Mon Jun 20, 2011 2:05 pm
- Location: saint louis
- Contact:
Re: oil pump/BBK question
was also wondering what mix to run
'86 Honda Spree : taz stage3 w/ mild porting, head milled 0.015", and pulley mod. 2k+ mies on kit
'80 Puch Magnum MKII
'78 Maxi Newport. Polini 64cc case matched, hi comp head, Rito alum crank, delorto 21mm race, etc.
'78 PA50 Hobbit
'80 Puch Magnum MKII
'78 Maxi Newport. Polini 64cc case matched, hi comp head, Rito alum crank, delorto 21mm race, etc.
'78 PA50 Hobbit