Where to mount eBay CDI ??

ringLord4 · Post by **ringLord4** » Sun Jul 07, 2013 6:46 pm

I bought this big ole hunk of junk from eBay, now I don't know where to mount it

: ImageUploadedByTapatalk1373237198.041261.jpg (112.69 KiB) Viewed 10615 times

This didn't work lol.

mousewheels · Post by **mousewheels** » Sun Jul 07, 2013 7:01 pm

General guideline for any electronics is - mout it away from water drip/splash/dirt/heat/vibration. Stock location is pretty good.

IMHO - the fins are overkill, but if you want - place them so airflow will do it's best for cooling.

patthesoundguy · Post by **patthesoundguy** » Sun Jul 07, 2013 9:20 pm

You could use a hose clamp and clamp it right where it is if it won't go in the stock location. Or maybe fab a bracket to mount it in the stock location.

Sent from my Nexus 7 using Tapatalk 2

deuce217 · Post by **deuce217** » Mon Jul 08, 2013 12:22 am

IMO I would mount that back in the box and return it. The Honda OEM part will be better for you in the long run, way less chance of leaving you, pushing your way home. But if you are unable to fund the honda one, next to the battery would be a good place. I am assuming this is a spree application.

ringLord4 · Post by **ringLord4** » Mon Jul 08, 2013 2:35 am

I have the oem. This was a test run

paulpauly7 · Post by **paulpauly7** » Mon Jul 08, 2013 2:40 am

any difference between the two cdis ? i just found a daytona adjustable cdi with 3 settings Street , Race , Full Race im gonna buy it and see what happens hopefully its good because its daytona honda oem

deuce217 · Post by **deuce217** » Mon Jul 08, 2013 4:54 am

paulpauly7 wrote:any difference between the two cdis ? i just found a daytona adjustable cdi with 3 settings Street , Race , Full Race im gonna buy it and see what happens hopefully its good because its daytona honda oem

I think the difference is just in the advancement and retarding of the spark. I would stick with OEM. Honda spends plenty of time finding out how to not have predetonation.

ringLord4 · Post by **ringLord4** » Mon Jul 08, 2013 9:03 pm

paulpauly7 wrote:any difference between the two cdis ? i just found a daytona adjustable cdi with 3 settings Street , Race , Full Race im gonna buy it and see what happens hopefully its good because its daytona honda oem

I noticed a little difference. Maybe a bit smoother and better response in around 10mph up. Not much though. Will do further testing and post results.

As far as honda OEM, ya they may be good but were in the 21st century now, its ok to look for improvements over the past 30 years

martynkim · Post by **martynkim** » Mon Jul 08, 2013 9:45 pm

Chinese have made no improvements in 30 years. I think they went backwards. I would send it back begging for a refund...

ringLord4 · Post by **ringLord4** » Mon Jul 08, 2013 11:49 pm

Astute review of China. Thank you. I'll probably send it back.

deuce217 · Post by **deuce217** » Tue Jul 09, 2013 12:05 am

Nothing wrong with trying new stuff. I just dont believe in chinese electronics. Japan has a level of pride in their products and engineering unparalleled, by any sweat shop in China. If your spree engine is at standard compression it will probable not harm anything. Now if you had high compression and were altering the ignition timing this would be much more risky. Have fun.

ringLord4 · Post by **ringLord4** » Tue Jul 09, 2013 1:14 am

Well my compression is gone right now. I have another thread going troubleshooting it

Honda Spree and Elite 50 Forums