dio reeds on non dio sr

Corey · Post by **Corey** » Thu Aug 21, 2008 9:06 am

I have a older elite sr (non Dio) will performance reeds that fit a dio fit my engine? if so will i have any problems with performance since my scoot is basically stock? i do plan on bigger carb and perf pipe like in a month of 2.

Corey · Post by **Corey** » Thu Aug 21, 2008 9:12 am

it is a dual boysden type reed setup all polished and pretty. and excepts keihin pwk or 21-30mm carbs will my stock fit for now?

DELETED · Post by **DELETED** » Mon Aug 25, 2008 2:48 am

DELETED

Dac · Post by **Dac** » Mon Aug 25, 2008 10:52 am

OH NO!

A bot?!?!?!? On this forum?!?!?!?
QUICK Ban him and update the bot protection!

Clivester · Post by **Clivester** » Tue Aug 26, 2008 7:44 pm

Corey wrote:I have a older elite sr (non Dio) will performance reeds that fit a dio fit my engine? if so will i have any problems with performance since my scoot is basically stock? i do plan on bigger carb and perf pipe like in a month of 2.

Can anyone answer this

I'd be interested to know too

Bump........ to get past the Manga thread hijack.

Clive

Kenny_McCormic · Post by **Kenny_McCormic** » Tue Aug 26, 2008 7:55 pm

I know they are both 4 bolt intake manifolds, but IDK if the parts interchange, try X referencing parts #s.

Dac · Post by **Dac** » Tue Aug 26, 2008 10:01 pm

the reed cages are different.
and dio reeds- 3 screws
non dio reeds- 2 screws.
so its not you could just do the reed it self ether.

sorry for the bad news dude.

Clivester · Post by **Clivester** » Wed Aug 27, 2008 1:56 am

Dac wrote:the reed cages are different.
and dio reeds- 3 screws
non dio reeds- 2 screws.
so its not you could just do the reed it self ether.

sorry for the bad news dude.

No, Kenny is right. The early SA50s and the Dios are both 4-bolt pattern into the crankcase. I think some race reeds are 3-screw, depending on the manifold used. The SBs and the Sprees are 2 bolt.

The parts diagrams are interesting. The pre-94 SA50 (mine is 88) shows 2 different reed cage/manifold set ups. There is one off to the side that looks identical to the set-up for the Dio models (same drawing), however, the part numbers corresponding to reference numbers in that diagram on the early SA50 are not listed in the parts table at 2 different web sites I have checked. It suggests they may be interchangeable, but not definitive. It really needs someone to have tried attaching a (e.g. CT) race manifold to an early SA50.

I guess if no-one knows, I could try calling Keoni at VTCycles when they open again Thursday.

Clive.

Dac · Post by **Dac** » Wed Aug 27, 2008 2:19 am

no im saying the reed cage. there is 3 screws holding the reed. and only two on the other.

Stock to stock it will not fit.
i can tell you that now. My reeds where messing up on my 96, so i took some off my 92 and there totally different.

Clivester · Post by **Clivester** » Wed Aug 27, 2008 2:56 am

I think Corey, the original poster, has aftermarket reeds plus racing manifold in mind. Is that right Corey?

Clive.

maddog · Post by **maddog** » Fri Aug 29, 2008 2:59 am

So what else does he have, i love stupidity

Clivester · Post by **Clivester** » Tue Sep 02, 2008 6:44 pm

maddog wrote:So what else does he have, i love stupidity

I think incest is illegal in most states.

Honda Spree and Elite 50 Forums

dio reeds on non dio sr

dio reeds on non dio sr

Wonderful

Re: Wonderful

Re: dio reeds on non dio sr