Carb Help!! PICTURES INSIDE!

vette76 · Post by **vette76** » Sun Sep 11, 2005 12:21 pm

still a carb proble. thats not what i was talking about. there are 3 pieces to the float. the float, the float pin, and the float needle. that small needle is a valve. make sure you have it. the float holds it and it is located on a little hole next to the pin. make sure it is fitting into the float guide nicely and operates back and fourth with the float. oil wont do anything on this. to be honest i would clean it off because it might do more harm then good.

Justinsane · Post by **Justinsane** » Sun Sep 11, 2005 1:27 pm

so judging by the picture? do i have all the float parts?

MySpree · Post by **MySpree** » Sun Sep 11, 2005 2:42 pm

you cant tell the float valve goes under the float it self and it connected to the inder side of the float by a groove.

Justinsane · Post by **Justinsane** » Sun Sep 11, 2005 2:53 pm

does anyone have a picture of what it all should look like/consist of?

MySpree · Post by **MySpree** » Sun Sep 11, 2005 3:27 pm

yes i will post one later tonight.

Justinsane · Post by **Justinsane** » Sun Sep 11, 2005 3:57 pm

well, i think im in trouble here,... becuase ive taken the carb apart 3 times today, and theres nothin in there except for the float, and pin.... there no needle jigglin around...

MySpree · Post by **MySpree** » Sun Sep 11, 2005 4:52 pm

hey i can help u out dont worry. if u need it i can send u a carb to use while urs is here and ill fix ur carb for ya. all clean it put some new gaskets and yea for free.

Justinsane · Post by **Justinsane** » Sun Sep 11, 2005 5:12 pm

i think we'll have to do that... but i wanna make sure that mine is 100% needing to be worked on... because i dont wanna put you through the trouble

K_OS · Post by **K_OS** » Sun Sep 11, 2005 6:44 pm

Before you do anything tighten the screw that I marked in the photo. This is a drain needle.

________________________________________________________________
Be Cool
K_OS

vette76 · Post by **vette76** » Sun Sep 11, 2005 7:24 pm

thats not going to help. the gas isnt coming out of the drain nipple.

K_OS · Post by **K_OS** » Sun Sep 11, 2005 7:26 pm

Oops my fault... that is what I get for not letting all the pictures load.

________________________________________________________________
Be Cool
K_OS

eager_beaver · Post by **eager_beaver** » Sun Sep 11, 2005 9:07 pm

make sure your bowl aint sticking, go buy carb cleaner mine did the same i cleaned it with carb cleaner and it works great

Justinsane · Post by **Justinsane** » Sun Sep 11, 2005 11:06 pm

ive tried everything,... im taking the carb apart again... 5th time.. tonight and taking pictures, because im convinced that im missing a float part.

hondaman · Post by **hondaman** » Sun Sep 11, 2005 11:32 pm

Your gonna need that float needle for the carb to run right. Also make sure your carb gasket is in good shape.

Justinsane · Post by **Justinsane** » Sun Sep 11, 2005 11:41 pm

ok, let me repeat.. i have no idea what a carb should look like, so i dont know if there are any parts missing, or where the specific parts are.

but these picture are of the float assembly... thats all that was in there... no other parts
that picture shows the floater, and the floater pin.. but no float needle... where is it/should it be??

this is a picture with the floater and float pin removed... is the float needle supposed to be somewhere under that???

WELL ITS NOT!

[/list]