Re: Checkin in, first post... here at least
Posted: Thu May 19, 2011 1:30 pm
I bet there is 0 difference between the 10 section and 13 section in the actual 'mufler' part
Honda Spree and Elite 50 Forums
Keeping Spree Elite Aero 50cc and Gyro Alive!
http://hondaspree.net/hondaspree.net/phpBB3/
Checkin in, first post... here at least
http://hondaspree.net/hondaspree.net/phpBB3/viewtopic.php?t=14885
Page 9 of 21
Re: Checkin in, first post... here at least
Posted: Thu May 19, 2011 10:02 pm
A few pictures
Re: Checkin in, first post... here at least
Posted: Thu May 19, 2011 10:11 pm
awesome man! Looks good so far! Thanks for the pictures! What are your takes on the overall condition of the engine at approx 5000 miles later?
Re: Checkin in, first post... here at least
Posted: Thu May 19, 2011 10:34 pm
not bad for 5000 miles
One of the bearings stuck to the crank....had to get it off with the bearing puller
One of the bearings stuck to the crank....had to get it off with the bearing puller
Re: Checkin in, first post... here at least
Posted: Thu May 19, 2011 10:36 pm
I see that. That sucks. How brittle do you think that 52mm bbk is? I hope we (you) aren't building a bomb!Trafficjamz wrote:not bad for 5000 miles
One of the bearings stuck to the crank....had to get it off with the bearing puller
Re: Checkin in, first post... here at least
Posted: Thu May 19, 2011 10:44 pm
Chicago Ben wrote:I see that. That sucks. How brittle do you think that 52mm bbk is? I hope we (you) aren't building a bomb!Trafficjamz wrote:not bad for 5000 miles
One of the bearings stuck to the crank....had to get it off with the bearing puller
I would get a CHT for sure
Re: Checkin in, first post... here at least
Posted: Thu May 19, 2011 11:13 pm
Ok just ordered the trail tech temp gauge from treatland, this should do justiceTrafficjamz wrote:I would get a CHT for sure
Re: Checkin in, first post... here at least
Posted: Thu May 19, 2011 11:51 pm
just pulled the trigger on a smoked kymco tail from vt
Re: Checkin in, first post... here at least
Posted: Sun May 22, 2011 6:06 pm
I wouldn't go that far, but I would bet that none of our scoots are tuned to the point of noticing the difference.Chicago Ben wrote:I bet there is 0 difference between the 10 section and 13 section in the actual 'mufler' part
Re: Checkin in, first post... here at least
Posted: Sun May 22, 2011 6:39 pm
umm there is a big difference.....
Re: Checkin in, first post... here at least
Posted: Sun May 22, 2011 6:39 pm
umm there is a big difference.....
Re: Checkin in, first post... here at least
Posted: Sun May 22, 2011 6:49 pm
Such as?fastplastic wrote:umm there is a big difference.....
Re: Checkin in, first post... here at least
Posted: Sun May 22, 2011 7:15 pm
There are more welds
Re: Checkin in, first post... here at least
Posted: Sun May 22, 2011 11:47 pm
You got me there Ben.Chicago Ben wrote:There are more welds
Re: Checkin in, first post... here at least
Posted: Mon May 23, 2011 2:14 am
Oh yes there is a huge differenceeliteguy50 wrote:Such as?fastplastic wrote:umm there is a big difference.....
That is the reason I want to find one of these 13 section pipes
It took Fastplastics ride from mild to wild when paired with a 28mm carb
At first glance these two pipes seem to be the same, but if you bring out the tape measure, you will see the are indeed different.