Page 3 of 3
Re: What Dio parts should Taz stock this year? I also need h
Posted: Tue Feb 21, 2012 11:51 pm
by kingkamehameha
Everyone is running either a mid scorp or a pg long. I would like to see a taz pipe made that could keep up with those.
Re: What Dio parts should Taz stock this year? I also need h
Posted: Wed Feb 22, 2012 12:41 am
by Dio89Elite
tazland001 wrote:When I get pics of the dio mufflers I will post. Then we should take a vote for fun.
I will check on some of the other parts.
Taz
yup. I'll be waiting patiently for those pics so I can vote. =).
I, too wouldn't mind a decent pipe that's around $150s.
I would like reeds, decent priced rollers that last, a clutch that's similar to the stage6 (doesn't need to be a particular brand), replacement belts, stainless assortment of metric bolts and screws and washers...
hey, it's a wish list right?
Re: What Dio parts should Taz stock this year? I also need h
Posted: Wed Feb 22, 2012 11:09 am
by tazland001
Im waiting on muffler pics. A taz muffler. I like the ring of that. hehehehe.
Its all the same stuff with just diff names. All these people buy from the same makers I use but they just put there name brand on it. funny funny.
Taz
Re: What Dio parts should Taz stock this year? I also need h
Posted: Wed Feb 22, 2012 1:34 pm
by Dio89Elite
here ye! here ye! buy it soon! available in limited quantities!
is your exhaust screaming like a banshee and still not going anywhere fast?
ditch it! and get the Taz Performance Exhaust pipe!
It'll rumble like the growling belly of a hungry Tazmanian Devil and make your scoot/ ped ride like a steed from Hades!
Disclaimer: performance gains depends on the fine tuning of an individual's application...
steed from Hades has not been properly tested for top speed using GPS...
[alrighty... so i was bored at work, even though I have tons of work stuff to do...
really.]
Re: What Dio parts should Taz stock this year? I also need h
Posted: Wed Feb 22, 2012 2:04 pm
by eliteguy50
that gives me an idea, a custom engine mount to swap a banshee engine into a ruckus.
Re: What Dio parts should Taz stock this year? I also need h
Posted: Wed Feb 22, 2012 3:58 pm
by Wheelman-111
Greetings:
Oh, and pulley boss shim washers! VT can't seem to get 'em. 15mm ID, 19mm OD, 2 or 3 thicknesses, how hard can it be?
Re: What Dio parts should Taz stock this year? I also need h
Posted: Fri Feb 24, 2012 6:59 pm
by phatkix
Chameleon factory pipes would be killer.
Re: What Dio parts should Taz stock this year? I also need h
Posted: Tue Feb 28, 2012 11:41 am
by tazland001
I am still shopping around on mufflers. d*** the dollar is getting really weak and the prices are going up on a lot of the parts.
I have a size on the belt. Is a 667*18 a good size????
I also ordered 24mm carbs this time
If you guys need jets tell me the sizes now or forever hold your peace. lol
Taz
Re: What Dio parts should Taz stock this year? I also need h
Posted: Tue Feb 28, 2012 11:59 am
by bakaracer
Odd weight rollers. Example. 6.2g,6.5g,6.7g,6.8g .
Re: What Dio parts should Taz stock this year? I also need h
Posted: Tue Feb 28, 2012 12:16 pm
by tazland001
Actually I have been wanting to bring in metric bolts, nuts, and washers. I will check into that.
Taz
Re: What Dio parts should Taz stock this year? I also need h
Posted: Tue Feb 28, 2012 12:38 pm
by Dio89Elite
tazland001 wrote:Actually I have been wanting to bring in metric bolts, nuts, and washers. I will check into that.
Taz
are these gonna be stainless steel? just wondering...
If you can get a hold of a blue anodized set of bolts, nuts and washers, that would replace the non-critical areas of an SB50, I'd buy it. =)
did someone mention bar ends? I'll need a set. yes, i'd prefer blue anodized.
Re: What Dio parts should Taz stock this year? I also need h
Posted: Tue Feb 28, 2012 7:18 pm
by phatkix
tazland001 wrote:Actually I have been wanting to bring in metric bolts, nuts, and washers. I will check into that.
Taz
Sweet, I'd take a set or two
