Honda Spree and Elite 50 Forums

Posted: **Thu Oct 17, 2013 1:58 pm**

Trust me, I'm all for slammed rides, but graphite is right about that shock angle. But as long as your prepared for it, then I say give her *!!! Any plans for slamming the front end??

Posted: **Thu Oct 17, 2013 9:53 pm**

low down all good

Posted: **Fri Oct 18, 2013 3:37 am**

graphite9 wrote:he will see when he rides it. Its not really rideable at that angle. The smallest bump and that metal will slice that tire open. You can build a dio spree low with a good shock angle. I did this build for a guy. Not my style but he is the customer. Its 8"stretched dio, slammed and rides like stock.

hi graphite9. your right i'm going for normal ride.
P.S sweet ride.

Posted: **Fri Oct 18, 2013 3:42 am**

Kevinstonge wrote:Trust me, I'm all for slammed rides, but graphite is right about that shock angle. But as long as your prepared for it, then I say give her *!!! Any plans for slamming the front end??

hi kevin. graphite9 is right i'll have to got for the normal ride height.

Posted: **Fri Oct 18, 2013 3:45 am**

the shock mount. it's strong.

Posted: **Fri Oct 18, 2013 3:56 am**

the welder is a 110v flux wire, no gas. cheap home depot.

Posted: **Fri Oct 18, 2013 4:00 am**

that should hold.

, if not? get a bigger welder

.

Posted: **Fri Oct 18, 2013 4:08 am**

graphite9 wrote:he will see when he rides it. Its not really rideable at that angle. The smallest bump and that metal will slice that tire open. You can build a dio spree low with a good shock angle. I did this build for a guy. Not my style but he is the customer. Its 8"stretched dio, slammed and rides like stock.

I see. I think i'm going to cut the metal by the rear wheel. i'll post a photo when I cut the rear off.

Posted: **Fri Oct 18, 2013 6:56 am**

cut it and run led lights at the rear that would look badass

Posted: **Sun Oct 20, 2013 3:43 am**

I welded and reinforced the frame.

I know my welder sucks. LOL
some guys don't add any metal to the frame. they just bolt the motor right to the frame and go.

Posted: **Sun Oct 20, 2013 3:47 am**

this is a primer sealer.

Posted: **Sun Oct 20, 2013 11:20 am**

That looks a little hairy, I would do a little more support on that motor mount area, but thats me and I plan on doing 70+ on my SpreeX50.

Posted: **Sun Oct 20, 2013 11:27 am**

LoveMyHonda
doing 70+ on my SpreeX50 hope to see that build!!!!!!!!!
swimmingfree

Posted: **Sun Oct 20, 2013 2:31 pm**

graphite9 wrote:What just happened with that motor mount welding? I hope your not mounting to the last outer set of holes.

hi graphite, the welder is a cheap flux wire type, but weld is strong. i'm not mounting to last holes. I kept them in case I reinstall my spree engine. and stand

Posted: **Sun Oct 20, 2013 3:35 pm**

LoveMyHonda wrote:That looks a little hairy, I would do a little more support on that motor mount area, but thats me and I plan on doing 70+ on my SpreeX50.

hi lovemyhonda, I'm only going about 57MPH, you can see on my GPS phone app.

9to1 gears. 72 polini corsa.

Honda Spree and Elite 50 Forums

First spree AF16 motor swap. more photos of motor work.

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap

Re: First spree AF16 motor swap