Page 1 of 2
Bent Crank/Dio Engine Swap
Posted: Mon Dec 26, 2005 1:22 am
by spreegusto
hi guys, ive been having a problem with my 8000+ mile 86 spree. every time i put a new top end on it, it only lasts about 200 miles then the rings snap because the crank is bent. all or most of the bearings are shot on that engine, and the transmission is going fast. with all this talk of the dio engine on here, i was wondering how difficult it would be to trash the tired engine and upgrade to a newer dio one
i just hate how much the cranks cost, and if i could just get a whole new engine instead of rebuilding one... especially an upgradable new engine
Posted: Mon Dec 26, 2005 2:12 am
by maddog
For the money and time involved i would just pick up a 94+elite, ebay had them all the time but i think the word got out on how you can build them up to insanity!
Posted: Mon Dec 26, 2005 2:50 am
by spreegusto
id really like to keep the spree body and swap the enigne, im a huge fan of spree style...
Posted: Mon Dec 26, 2005 9:59 am
by MySpree
hellow im selling a dio in the for sale section!
Posted: Mon Jan 02, 2006 8:40 pm
by hrnytrtlsgsxr
for that conversion you will have to move the shock mounting bolt farther back and get an 87 motor mount. The 87 moto mount would be the fastes and easiest to do. Cut the sides of the mount to fit in the spree frame.The rubber boot of the 87 mount will just fit in the front tube of the spree frame. An elite S motor mount will need cutting and welding done on the tungue.As for the motor side of the 87. You have to drill that out. i would suggest putting in a (class
3/8 inch bolt. You can go with the correct mm bolt but it is ubber expensive at the legth you will need and the sizes are very close to each other. The class 8 bolt is designated by 5 stripes on the top of the hex head. Hope this helps.
Posted: Mon Jan 02, 2006 9:25 pm
by sulfuraciddd
do that upgrade im sure you wont be dissapointed with the potential performance you can get out of them
Posted: Mon Jan 02, 2006 9:35 pm
by hrnytrtlsgsxr
this is what a spree could look like with the 87 motor mount and moved shock mount. it all fits in with no plastic cutting.
Posted: Mon Jan 02, 2006 11:51 pm
by deathwish
wow thats a good looking spree.... nice job
Posted: Mon Jan 02, 2006 11:52 pm
by bitteraspects
indeed it is. or was should i say
Posted: Tue Jan 03, 2006 3:05 am
by hrnytrtlsgsxr
bitteraspects wrote:indeed it is. or was should i say
hahah yeah now it's someone elses
Posted: Tue Jan 03, 2006 3:08 am
by bitteraspects
yeah but looks pretty much the same right?
Posted: Tue Jan 03, 2006 3:20 am
by hrnytrtlsgsxr
bitteraspects wrote:yeah but looks pretty much the same right?
indeed it does.damm and i built that from scratch.
Posted: Tue Jan 03, 2006 3:25 am
by bitteraspects
must have been hard to let go
Posted: Tue Jan 03, 2006 3:32 am
by hrnytrtlsgsxr
bitteraspects wrote:must have been hard to let go
yup but i had to since i got the G. Thems was da rules.
Posted: Tue Jan 03, 2006 3:35 am
by bitteraspects
well it was a good swap then, i would have done it in a heartbeat