Page 1 of 21
Sprelite The Begining Of My Epic Build
Posted: Thu Apr 07, 2011 10:21 pm
by SpreeMadness520
Here are my plans,
50mm Taiwan bore with CHT gauge
Keli or Polini Performance Clutch (1500k)
Some Type Of Racing Variator
And 9 To 1 Gears.
Looking For A Throttle Cable For The Dio And Probably Brake Cable. Hit Me Up Thanks
Re: Sprelite The Begining Of My Epic Build
Posted: Thu Apr 07, 2011 11:29 pm
by Trafficjamz
The spree you rode had 9.1:1 gears
My elite had 8.4:1 gears
9.1:1 gears on a 85cc spree/dio will be a wheelie machine
Re: Sprelite The Begining Of My Epic Build
Posted: Fri Apr 08, 2011 12:45 pm
by fastplastic
mine with non worn out tranny parts is a wheelie machine..... look more towards 7.9 or 8.4s
Re: Sprelite The Begining Of My Epic Build
Posted: Fri Apr 08, 2011 3:42 pm
by SpreeMadness520
fastplastic wrote:mine with non worn out tranny parts is a wheelie machine..... look more towards 7.9 or 8.4s
I really liked the elites gearing so i will try to get 8.4s or any other good suggestion
Re: Sprelite The Begining Of My Epic Build
Posted: Fri Apr 08, 2011 6:44 pm
by SpreeMadness520
Is 99mm off the left side of the elite engine mount correct?
Re: Sprelite The Begining Of My Epic Build
Posted: Fri Apr 08, 2011 6:45 pm
by SpreeMadness520
How much do I take off of the top part?
Re: Sprelite The Begining Of My Epic Build
Posted: Fri Apr 08, 2011 11:32 pm
by Trafficjamz
We measured the stock Elite E Mount. Then marked it on the Elite S mount.
You can do the same with the spree mount.
Re: Sprelite The Begining Of My Epic Build
Posted: Sat Apr 09, 2011 11:02 am
by SpreeMadness520
Ok I See That Doesnt Seem To Hard How Much Do I Take Off Of The Top Part With The Rubber Bumper?
Re: Sprelite The Begining Of My Epic Build
Posted: Sat Apr 09, 2011 8:36 pm
by SpreeMadness520
Re: Sprelite The Begining Of My Epic Build
Posted: Sat Apr 09, 2011 8:40 pm
by SpreeMadness520
Engine Off, Cutting The Elite Mount Monday
Re: Sprelite The Begining Of My Epic Build
Posted: Sat Apr 09, 2011 8:41 pm
by SpreeMadness520
Still Need To Know How Much To Take Off Of The Stem W/Bumber
Re: Sprelite The Begining Of My Epic Build
Posted: Sun Apr 10, 2011 4:53 am
by Trafficjamz
SpreeMadness520 wrote:Still Need To Know How Much To Take Off Of The Stem W/Bumber
Enuff so the rubber bumper is in the middle of the hole on the frame.
Re: Sprelite The Begining Of My Epic Build
Posted: Sun Apr 10, 2011 10:17 am
by SpreeMadness520
Trafficjamz wrote:SpreeMadness520 wrote:Still Need To Know How Much To Take Off Of The Stem W/Bumber
Enuff so the rubber bumper is in the middle of the hole on the frame.
Ok can I use a spree shock? I think the bolt I need is M10 140mm.
Re: Sprelite The Begining Of My Epic Build
Posted: Sun Apr 10, 2011 1:39 pm
by SpreeMadness520
Wow that cut is going to be real close to the arm
Re: Sprelite The Begining Of My Epic Build
Posted: Sun Apr 10, 2011 6:08 pm
by SpreeMadness520
Cut the metal piece off of the spree mount
