Page 1 of 1

Anything i should do before i install my 44BBK?

Posted: Mon Jul 25, 2011 2:49 pm
by miglia-spyder
I bought a really nice spree that needed a rebuild. I have a 44bbk on the way from Taz. I have a couple questions... I planned on switching to pre-mix, Ive read a couple threads and heard a couple different numbers for the Ratio... What ratio should i be using with this kit? What spark plug? Will I need to clean up the cylinder at all before i install it?

Anything else i should do to get this thing ready for a BBK?

Re: Anything i should do before i install my 44BBK?

Posted: Mon Jul 25, 2011 4:36 pm
by sprite2011
Before your .parts come in begin researching here in the forums. Type is keywords in the "search" box. Also, the wikispreedia in the board index should tell you everything you need to know. Good luck!

Re: Anything i should do before i install my 44BBK?

Posted: Mon Jul 25, 2011 4:39 pm
by fastplastic
32:1 and b6hs would be my suggestion.....

Re: Anything i should do before i install my 44BBK?

Posted: Mon Jul 25, 2011 6:19 pm
by Mystic
i would think the bpr8h would be better :D

Re: Anything i should do before i install my 44BBK?

Posted: Tue Jul 26, 2011 9:37 am
by miglia-spyder
Perfect! Yeah i have been doing alot of reading on wikispreedia. And ive built plenty of two and 4 stroke small engines... Just checking to see if their was anything i should know in order to make it go smoothly.

Thanks for your help!

Re: Anything i should do before i install my 44BBK?

Posted: Tue Jul 26, 2011 9:47 am
by pboost
Tips from when i installed my bbk. Make sure you look at the ports in the new jug for any flashing/burs and if any hit it with a mild sand paper or dremel wheel to knock burs off etc. Also make sure the circ clips are in very good double triple check if you can use a small socket to push them in flush.

Re: Anything i should do before i install my 44BBK?

Posted: Tue Jul 26, 2011 9:48 am
by fastplastic
Mystic wrote:i would think the bpr8h would be better :D
think all u want don't hurt ur self lol :) :)

Re: Anything i should do before i install my 44BBK?

Posted: Tue Jul 26, 2011 10:45 am
by Mystic
dont get me confused fastplastic, no amount of thinking could hurt...its the doing that causes all the damage heheheh :D havent had ANY problems with the 8 personally

Re: Anything i should do before i install my 44BBK?

Posted: Tue Jul 26, 2011 10:57 am
by fastplastic
My 44mm ran a 6 plug never had any problems, but with my 72cc dio spree i run a b8hs per bakaracers suggestion just because.....

Re: Anything i should do before i install my 44BBK?

Posted: Tue Jul 26, 2011 11:20 am
by Mystic
I am running the 8 in my stock Spree :D I live in the south where its super hot already so that probably makes a difference, i guess riding around the corner etc it doesnt really matter about the 6 or the 8 but long distances at WOT surely benefits from any measures taken to prevent overheating which can damage your engine over time

Re: Anything i should do before i install my 44BBK?

Posted: Tue Jul 26, 2011 12:05 pm
by fastplastic
K

Re: Anything i should do before i install my 44BBK?

Posted: Tue Jul 26, 2011 4:36 pm
by Bear45-70
fastplastic wrote:
Mystic wrote:i would think the bpr8h would be better :D
think all u want don't hurt ur self lol :) :)
I agree that the 8 would be a better choice.