Page 1 of 1
how much is too much? modding the jug
Posted: Wed Mar 21, 2012 3:44 pm
by Trafficjamz
Is it ok to cut the section at the bottom of the jug that can be seen through the intake widows in the block ?
I will try to take a picture of what I am talking about.
Re: how much is too much? modding the jug
Posted: Wed Mar 21, 2012 4:11 pm
by bakaracer
yeah you can. look at your stroker bore as an example.
Re: how much is too much? modding the jug
Posted: Wed Mar 21, 2012 5:36 pm
by Trafficjamz
bakaracer wrote:yeah you can. look at your stroker bore as an example.
Yeah the 125 jug has no side skirts at all.
the polini jug has very high skirts.
Re: how much is too much? modding the jug
Posted: Wed Mar 21, 2012 10:51 pm
by iceman77
is that my bore? if so i like the way it's looking.
TJ
Re: how much is too much? modding the jug
Posted: Wed Mar 21, 2012 11:00 pm
by Trafficjamz
iceman77 wrote:is that my bore? if so i like the way it's looking.
TJ
Yes sir. Now I am just waiting for autotech355 to send gears. tiawan is far away
some port work by jamz
side skirts compared to polini bore
Re: how much is too much? modding the jug
Posted: Wed Mar 21, 2012 11:18 pm
by bakaracer
if your going to leave the intake port on the block that size, at least round the top and smooth out the side more so it doesnt cause to much turbulance.
Re: how much is too much? modding the jug
Posted: Wed Mar 21, 2012 11:21 pm
by Trafficjamz
bakaracer wrote:if your going to leave the intake port on the block that size, at least round the top and smooth out the side more so it doesnt cause to much turbulance.
I will do that
Re: how much is too much? modding the jug
Posted: Thu Mar 22, 2012 12:32 am
by kingkamehameha
Looks good traffic. What size carb and jets you planning on running? Does a block with a matched boost and ported intake port require bigger jets because there is more flow or smaller jets because it runs more efficient????!!
Re: how much is too much? modding the jug
Posted: Thu Mar 22, 2012 12:37 am
by Trafficjamz
ported = smaller jets
Re: how much is too much? modding the jug
Posted: Thu Mar 22, 2012 1:30 am
by Trafficjamz
Trafficjamz wrote:bakaracer wrote:if your going to leave the intake port on the block that size, at least round the top and smooth out the side more so it doesnt cause to much turbulance.
I will do that
I got it opened up a little more.
I will go back over it tomorrow with some cartridge rolls.
Re: how much is too much? modding the jug
Posted: Tue Mar 27, 2012 3:03 am
by damnSA50
On my Malossi bbk for the af05 the exhaust port isnt quite circular, think I should bore it out? Im thinking I should wait till I get a bigger carb first, this stock one might be the pin in my grenade.
Re: how much is too much? modding the jug
Posted: Tue Mar 27, 2012 3:04 am
by damnSA50
Oh ya traffic, I show everyone I know your photobucket race vs the honda civic or whatever that thing was. Thats a bad * scooter.
Re: how much is too much? modding the jug
Posted: Tue Mar 27, 2012 8:24 am
by swimmingfree
hopping to see what kind of rpm and what other info you get from this motor...good read so far ... what is the gool of this motor racing ???
swimmingfreee
Re: how much is too much? modding the jug
Posted: Wed Mar 28, 2012 8:21 am
by iceman77
swimmingfree wrote:hopping to see what kind of rpm and what other info you get from this motor...good read so far ... what is the gool of this motor racing ???
swimmingfreee
nope not racing but a daily driver
TJ